loading
reading
writing
saving
searching
Hydrulics - $1 (Stanwood)
QR Code Link to This Post
Hyd Pump, 1-11.5 FNPT in, 3/4-15 FNPT out. $5
Hyd Pump, 24500-5000, 1-11.5 FNPT ports, Outer half on spine shaft is stripped, but inner half is fine $5
Hyd Motor, P-10005, 7/8" shaft, 10" x 4" x 4" overall. $10
Ball valve, 1/2", 4,500 Psi working pressure, Stainless Steel. $5
Misc. Valves: I have many hand operate valves of all types (Ball, needle, diverter, etc.)
and sizes (1/4" to 3/4") $1 to $10
Relief and Check Valves:
3ea. 1/2" Adjustable relief, Dragon C12012-k 6,000 psi. $10ea. or 3 for $25
1ea. Vinson Adjustable relief, 1000-2300 range, Currently set to 1065 psi. $10
1ea. Teledyne 3/4" check valve, 5000 PSI, 3/4" F-NPT ports. $10
1ea. Parker 3/8" Adjustable relief, 5000 psi. $10
Directional Control Valve, GRE-SEN 300, single Spool, Open-Center, 3/4" F-NPT outlet ports. $25
Directional Control Valve, 3 Spool, Open-Center, 3/4" F-NPT Feed ports. I have 2, $50 ea. or $80 for both.
Double Pilot Operated Hydraulic Check Valve (Almost 100% that's what this is). A Double Pilot Operated Hydraulic Check Valve is used to hold hydraulic cylinders and prevent them from drifting down while your directional control valve is in the neutral position. Prevents a load from falling if a hose ever fails. SAE 3/4-16 O-ring seal J1926-1 Ports. $20.
Hyd Cylinder (Bridgeport Mill Knee). This good functional unit came out of a Bridgeport series 1 tracer mill. The hyd power unit that drove it ran at 500 PSI. I don't know what max PSI is. The knee crank handle operated the screw with a range of 19". The Hyd stroke is 6". Min LOA is 14", Body is 5" x 14", Ports are 1/4" F-NPT. Bore is approx, 4.25", Ram is 2.5". It weights 75 lbs. $15
Hyd Cylinder (Bridgeport Y Axis). This good functional unit came out of a Bridgeport series 1 tracer mill. The hyd power unit that drove it ran at 500 PSI. I don't know what max PSI is. The body dia. is 5", mounting flange is 7". LOA (retracted) is 21" and Hyd Stroke is 12.5", Bore is approx. 3.75", Ram is 1.25", Weight = 50 lbs, ports are 1/4" F-NPT. $15
Hyd Cylinder. Used CROSS DB series HYDRAULIC CYLINDER, 1.5" bore, 8" Stroke, 3/4" ROD, 5/8" Pins, 1/2" F-NPT ports, 2500 psi, 17" pin centers retracted. $15
Hyd Cylinder. Used HYDRAULIC CYLINDER, 2+" bore, 14" Stroke, 1" ROD, ?" Pins, ?" F-NPT ports, 31.5" pin centers retracted. $25
60' 3000 psi Hydraulic Hose. Good condition 60 foot Hydraulic hose marked 6M3K 3/8" (9.5mm) 3000Psi (21.0 MPA). 3/8" JIC female fitting (one end) and open on other end. Included is 10' length with fitting on one end. I cut out small section of over 72' hose that was damaged due to improper installation. $15
Misc. Hyd Hose. Removed from working equipment, Many sizes (3/8 to 1"), Lengths (3' to 60'), Pressures (low for return lines to 5000 PSI), Most have connectors. $1 to $15
Pressure Gauge, New-Old-Stock condition 3.000 psi (200 bar) liquid filled pressure gauge. Fauver # LFG-2-300P. 2-1/2" dia. 1/4" M-NPT connection. $7.50
Pressure Gauge, 2,000 psi, working condition but needs glycerin refill, the rubber fill stop got pushed aside in storage and it lost most of the damping fluid. 1/4" M-NPT connection. $3
Hyd Fittings #1 - All NOS
A. 3/4-14 M-NPT(*) to 1/4-18 F-NPT, 2 @ $1 ea.
B. 3/4-14 M-NPT(*) to 1/2-14 F-NPT, 8 @ $1 ea.
C. 3/4-14 M-NPT to 3/8-18 F-NPT, 4 @ $1 ea.
D. 3/4-14 M-NPT to 3/4-14 M-NPT, 3 @ $1 ea
E. 3/4-14 M-NPT Street, 5 @ $2 ea.
F. 3/4-14 M-NPT Union, 316 SS, 1 @ $4 ea.
G. 3/4-14 M-NPT Straight Coupler, 1 @ $1 ea.
H. 3/4-14 M-NPT(*) 90 degree, 1 @ $1 ea.
I. 3/4-14 M-NPT(*) to 3/4" Hose barb, 1 @ $1 ea
J. 3/4-14 M-NPT(*) to 3/4-14 F-NPS, 8 @ $1 ea.
Hyd Fittings #2 - All NOS
K. 1/2-14 M-NPT(*) Straight Coupler, 4 @ $1 ea.
L. 1/2-14 M-NPT(*) to 1/2-14 F-NPS, 45 degree, 2 @ $1 ea.
M. 1/2-14 M-NPT(*) to 1/2-14 F-NPS, 90 degree, 8 @ $1 ea.
N. 1/2-14 M-NPT to 1/2-14 F-NPS, 1 @ $1 ea.
O. 1/2-14 M-NPT(*) to 3/8-18 F-NPS, 3 @ $1 ea.
P. 3/8-18 M-NPT(*) to 3/8-18 F-NPS, 90 degree, 5 @ $1 ea.
Q. 1/2-14 M-NPT(*) to 3/8-18 F-NPT, Reducer, 2 @ $1 ea.
R. 3/4-14 M-NPT(*) to 3/4-14 F-NPS, 45 degree, 1 @ $1 ea.
S. 3/8-18 M-NPT(*) to 3/8-18 M-NPT, 4 @ $1 ea.
T. 1/4-18 M-NPT(*) to 1/4-18 M-NPT, 2 @ $1 ea.
U. 1/4-18 M-NPT(*) to 1/4-18 F-NPS, 45 degree, 2 @ $1 ea.
V. 1/4-18 M-NPT(*) to 1/4-18 F-NPS, 2 @ $1 ea.
U. 1/4-18 M-NPT(*) to 1/4-18 F-NPS, 90 degree, 1 @ $1 ea.
(*) This M-NPT (National Pipe Taper) fitting end has 30 degree interior chamfer. Which makes it compatable with both F-NPS (National Pipe Straight) and F-NPT fittings.
More to come.
Note: I'm very interested in unloading most of my 60 year collection of Stuff.
The more you buy the cheaper it gets. Check out the other items I have posted.
You won’t believe the price you’ll get if you were to buy all the above HYD items.